Added missing call to scanFinished=true.
This was causing the percent and eta to never get
printed for backup progress even after the scan was finished.
The StdioWrapper is not used at all by the ProgressPrinters. It is
called a bit earlier than previously. However, as the password prompt
directly accessed stdin/stdout this doesn't cause problems.
The status bar got stuck once the first error was reported, the scanner
completed or some file was backed up. Either case sets a flag that the
scanner has started.
This flag is used to hide the progress bar until the flag is set. Due to
an inverted condition, the opposite happened and the status stopped
refreshing once the flag was set.
In addition, the scannerStarted flag was not set when the scanner just
reported progress information.
We always need both values, except in a test, so we don't need to lock
twice and risk scheduling in between.
Also, removed the resetting in Done. This copied a mutex, which isn't
allowed. Static analyzers tend to trip over that.
The channel-based algorithm had grown quite complicated. This is easier
to reason about and likely to be more performant with very many
CompleteBlob calls.
When backing up many small files, the unbuffered channels frequently
cause the FileSaver to block when reporting progress information. Thus,
add buffers to these channels to avoid unnecessary scheduling.
As the status information is purely informational, it doesn't matter
that the status reporting shutdown is somewhat racy and could miss a few
final updates.
This can be used to check how large a backup is or validate exclusions.
It does not actually write any data to the underlying backend. This is
implemented as a simple overlay backend that accepts writes without
forwarding them, passes through reads, and generally does the minimal
necessary to pretend that progress is actually happening.
Fixes #1542
Example usage:
$ restic -vv --dry-run . | grep add
new /changelog/unreleased/issue-1542, saved in 0.000s (350 B added)
modified /cmd/restic/cmd_backup.go, saved in 0.000s (16.543 KiB added)
modified /cmd/restic/global.go, saved in 0.000s (0 B added)
new /internal/backend/dry/dry_backend_test.go, saved in 0.000s (3.866 KiB added)
new /internal/backend/dry/dry_backend.go, saved in 0.000s (3.744 KiB added)
modified /internal/backend/test/tests.go, saved in 0.000s (0 B added)
modified /internal/repository/repository.go, saved in 0.000s (20.707 KiB added)
modified /internal/ui/backup.go, saved in 0.000s (9.110 KiB added)
modified /internal/ui/jsonstatus/status.go, saved in 0.001s (11.055 KiB added)
modified /restic, saved in 0.131s (25.542 MiB added)
Would add to the repo: 25.892 MiB
mintty on windows always uses pipes to connect stdout between processes
and for the terminal output. The previous implementation always assumed
that stdout connected to a pipe means that stdout is displayed on a
mintty terminal. However, this detection breaks when using pipes to
connect processes and for powershell which uses pipes when redirecting
to a file.
Now the pipe filename is queried and matched against the pattern used by
msys / cygwin when connected to the terminal. In all other cases assume
that a pipe is just a regular pipe.
Previously the progress bar / status update interval used
stdoutIsTerminal to determine whether it is possible to update the
progress bar or not. However, its implementation differed from the
detection within the backup command which included additional checks to
detect the presence of mintty on Windows. mintty behaves like a terminal
but uses pipes for communication.
This adds stdoutCanUpdateStatus() which calls the same terminal detection
code used by backup. This ensures that all commands consistently switch
between interactive and non-interactive terminal mode.
stdoutIsTerminal() now also returns true whenever stdoutCanUpdateStatus()
does so. This is required to properly handle the special case of mintty.
