This commit changes the internal file system implementation for reading
data from stdin, it now returns an error when no bytes could be read. I
think it's worth failing in this case, the user instructed restic to
read some data from stdin, and no data was read at all. Maybe it was in
a pipe and some earlier stage failed.
See #2135 for a short discussion.
When the scanner is slower than the actual backup, the tomb cancels the
context passed to Scan(), which then returns ctx.Err(). In the end, the
main function prints an error message that is not helpful ("Context
cancelled") and exits with an error code although no error occurred.
The code now ignores the error in the context and just uses it for
cancellation. The scanner is not supposed to return an error anyway.
Closes #1978
Adds a SelectByName method to the archive and scanner which only require
the filename as input, and can thus be run before calling lstat on the
file. Can speed up scanning significantly if a lot of filename excludes
are used.
When the archiver is faster than the scanner, restic deadlocks. This
commit adds a `finished` channel to the struct in `ui/backup.go` so that
scanner results are ignored when the archiver is already finished.
Closes #1834
This commit changes how the worker goroutines for saving e.g. blobs
interact. Before, it was possible to get stuck sending an instruction to
archive a file or dir when no worker goroutines were available any more.
This commit introduces a `done` channel for each of the worker pools,
which is set to the channel returned by `tomb.Dying()`, so it is closed
when the first worker returned an error.
This commit changes the archiver so that low-level errors saving data to
the repo are returned to the caller (instead of being handled by the
error callback function). This correctly bubbles up errors like a full
temp file system and makes restic abort early and makes all other worker
goroutines exit.
The previous code tried to be as efficient as possible and only do a
single open() on an item to save, and then fstat() on the fd to find out
what the item is (file, dir, other). For normal files, it would then
start reading the data without opening the file again, so it could not
be exchanged for e.g. a symlink.
This behavior starts the watchdog on my machine when /dev is saved
with restic, and after a few seconds, the machine reboots.
This commit reverts the behavior to the strategy the old archiver code
used: run lstat(), then decide what to do. For normal files, open the
file and then run fstat() on the fd to verify it's still a normal file,
then start reading the data.
The downside is that for normal files we now do two stat() calls
(lstat+fstat) instead of only one. On the upside, this does not start
the watchdog. :)
As mentioned in issue [#1560](https://github.com/restic/restic/pull/1560#issuecomment-364689346)
this changes the signature for `backend.Save()`. It now takes a
parameter of interface type `RewindReader`, so that the backend
implementations or our `RetryBackend` middleware can reset the reader to
the beginning and then retry an upload operation.
The `RewindReader` interface also provides a `Length()` method, which is
used in the backend to get the size of the data to be saved. This
removes several ugly hacks we had to do to pull the size back out of the
`io.Reader` passed to `Save()` before. In the `s3` and `rest` backend
this is actively used.
A user discovered[1] that when the backup finishes during the upload of
an intermediate index, the upload is cancelled and the index never fully
saved, but the snapshot is saved and the backup finalizes without an
error. This lead to a situation where a snapshot references data that is
contained in the repo, but not referenced in any index, leading to
strange error messages.
This commit uses a dedicated context to signal the intermediate index
uploading routine to terminate after the last index has been uploaded.
This way, an upload running when the backup finishes is completed before
the routine terminates and the snapshot is saved.
[1] https://forum.restic.net/t/error-loading-tree-check-prune-and-forget-gives-error-b2-backend/406
Index.Has() is a faster then Index.Lookup() for checking if a blob exists
in the index. As the returned data is never used, this avoids a ton
of allocations.
