This deprecates the current minDiskFreePct setting and introduces
minDiskFree. The latter is, in it's serialized form, a string with a
unit. We accept percentages ("2.35%") and absolute values ("250 k", "12.5
Gi"). Common suffixes are understood. The config editor lets the user
enter the string, and validates it.
We still default to "1 %", but the user can change that to an absolute
value at will.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/4087
LGTM: AudriusButkevicius, imsodin
This adds a new config AllowedNetworks per device, which when set should
contain a list of network prefixes (192.168.0.0/126 etc) that are
allowed for the given device. The connection service will not attempt
connections to addresses outside of the given networks and incoming
connections will be rejected as well.
I've added the config to the normal device editor and shown it (when
set) in the device summary on the main screen.
There's a unit test for the IsAllowedNetwork method, I've done some
manual sanity testing on top of that.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/4073
One more step on the path of the great refactoring. Touches rwfolder a
little bit since it uses the Lstat from fs as well, but mostly this is
just on the scanner as rwfolder is scheduled for a later refactor.
There are a couple of usages of fs.DefaultFilesystem that will in the
end become a filesystem injected from the top, but that comes later.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/4070
LGTM: AudriusButkevicius, imsodin
Adds a unit test to ensure we don't scan symlinks on Windows. For the
rwfolder, trusts that the logic in the invalid check is correct and that
the check is actually called from the need loop.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/4042
Basically, if we don't care about the sync status of the file we should
not tag someone else out of sync because they don't have the latest
version. This solves *my* "Syncing - 100%" scenario at least.
The reason this happens seems to be like this, in my situation. I have
three devices, connected in a "line": A-B-C. A is a Mac and litters
.DS_Store files everywhere. I've ignored these, but some escaped into
the folders before I did so. I've also ignored them on B and C but at
different stages. B was flagging C as out of sync, because at the point
the ignores were introduced C had a lower version of .DS_Store than A.
Now none of them are sending updates about it any more since it's
ignored...
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3981
Other routines use atomics, hence even if we are under a lock, we should
too.
We might atomically store with
Not sure how it happens, but it's between lines
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3974
After this change,
- Symlinks on Windows are always unsupported. Sorry.
- Symlinks are always enabled on other platforms. They are just a small
file like anything else. There is no need to special case them. If you
don't want to sync some symlinks, ignore them.
- The protocol doesn't differentiate between different "types" of
symlinks. If that distinction ever does become relevant the individual
devices can figure it out by looking at the destination when they
create the link.
It's backwards compatible in that all the old symlink types are still
understood to be symlinks, and the new SYMLINK type is equivalent to the
old SYMLINK_UNKNOWN which was always a valid way to do it.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3962
LGTM: AudriusButkevicius
Instead of just immediately dropping the event if the subscription isn't
ready to receive it, give it 15 ms to catch up. The value 15 ms is
grabbed out of thin air - it just seems reasonable to me.
The timer juggling makes the event send pretty much exactly twice as
slow as it was before, but we're still under a microsecond. I think it's
negligible compared to whatever event that just happened that we're
interested in logging (usually a file operation of some kind).
benchmark old ns/op new ns/op delta
BenchmarkBufferedSub-8 475 950 +100.00%
benchmark old allocs new allocs delta
BenchmarkBufferedSub-8 4 4 +0.00%
benchmark old bytes new bytes delta
BenchmarkBufferedSub-8 104 117 +12.50%
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3960
Instead of
[I6KAH] 19:05:56 INFO: Single thread hash performance is 359 MB/s using minio/sha256-simd (354 MB/s using crypto/sha256).
it now says
[I6KAH] 19:06:16 INFO: Single thread SHA256 performance is 359 MB/s using minio/sha256-simd (354 MB/s using crypto/sha256).
[I6KAH] 19:06:17 INFO: Actual hashing performance is 299.01 MB/s
which is more informative. This is also the number it reports in usage
reporting.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3918
Can't do what I did, as the rolling function is not the same as the
non-rolling one. Instead this uses an improved version of the rolling
adler32 to accomplish the same thing. (PR filed on upstream, so should
be able to use that directly in the future.)
The rolling version of adler32 is just a wrapper around the standard
hash/adler32 when used in a non-rolling fashion, but it's inefficient as
it allocates a new hash instance for every Write(). This uses the
default version instead in the block hasher, and adds a test to verify
the result is the same as they were before. It reduces allocations by
88% and increases speed about 5%.
benchmark old ns/op new ns/op delta
BenchmarkHashFile-8 64434698 61303647 -4.86%
benchmark old MB/s new MB/s speedup
BenchmarkHashFile-8 276.65 290.78 1.05x
benchmark old allocs new allocs delta
BenchmarkHashFile-8 1238 150 -87.88%
benchmark old bytes new bytes delta
BenchmarkHashFile-8 17877363 49292 -99.72%
