This adds our short device ID to the basic auth realm. This has at least
two consequences:
- It is different from what's presented by another device on the same
address (e.g., if I use SSH forwards to different dives on the same
local address), preventing credentials for one from being sent to
another.
- It is different from what we did previously, meaning we avoid cached
credentials from old versions interfering with the new login flow.
I don't *think* there should be things that depend on our precise realm
string, so this shouldn't break any existing setups...
Sneakily this also changes the session cookie and CSRF name, because I
think `id.Short().String()` is nicer than `id.String()[:5]` and the
short ID is two characters longer. That's also not a problem...
This adds the ability to have multiple concurrent connections to a single device. This is primarily useful when the network has multiple physical links for aggregated bandwidth. A single connection will never see a higher rate than a single link can give, but multiple connections are load-balanced over multiple links.
It is also incidentally useful for older multi-core CPUs, where bandwidth could be limited by the TLS performance of a single CPU core -- using multiple connections achieves concurrency in the required crypto calculations...
Co-authored-by: Simon Frei <freisim93@gmail.com>
Co-authored-by: tomasz1986 <twilczynski@naver.com>
Co-authored-by: bt90 <btom1990@googlemail.com>
all: Add package runtimeos for runtime.GOOS comparisons
I grew tired of hand written string comparisons. This adds generated
constants for the GOOS values, and predefined Is$OS constants that can
be iffed on. In a couple of places I rewrote trivial switch:es to if:s,
and added Illumos where we checked for Solaris (because they are
effectively the same, and if we're going to target one of them that
would be Illumos...).
Consistently use double dashes and fix typos -conf, -data-dir and
-verify.
Applies also to tests running the syncthing binary for consistency.
* Fix mismatched option name --conf in cli subcommand.
According to the source code comments, the cli option flags should
mirror those from the serve subcommand where applicable. That one is
actually called --config though.
* cli: Fix help text option placeholders.
The urfave/cli package uses the Value field of StringFlag to provide a
default value, not to name the placeholder. That is instead done with
backticks around some part of the Usage field.
* cli: Add missing --data flag in subcommand help text.
The urfave/cli based option parsing uses a fake flags collection to
generate help texts matching the used global options. But the --data
option was omitted from it, although it is definitely required when
using --config as well. Note that it cannot just be ignored, as some
debug stuff actually uses the DB:
syncthing cli --data=/bar --config=/foo debug index dump
This is a mostly pointless change to make security scanners and static
analysis tools happy, as they all hate seeing md5. None of our md5 uses
were security relevant, but still. Only visible effect of this change is
that our temp file names for very long file names become slightly longer
than they were previously...
With this change we emulate a case sensitive filesystem on top of
insensitive filesystems. This means we correctly pick up case-only renames
and throw a case conflict error when there would be multiple files differing
only in case.
This safety check has a small performance hit (about 20% more filesystem
operations when scanning for changes). The new advanced folder option
`caseSensitiveFS` can be used to disable the safety checks, retaining the
previous behavior on systems known to be fully case sensitive.
Co-authored-by: Jakob Borg <jakob@kastelo.net>
- In the few places where we wrap errors, use the new Go 1.13 "%w"
construction instead of %s or %v.
- Where we create errors with constant strings, consistently use
errors.New and not fmt.Errorf.
- Remove capitalization from errors in the few places where we had that.
Adds a new folder state "Waiting to Sync" in the same vein as the
existing "Waiting to Scan". This vastly improves performances in the
rare cases when there are lots and lots of folders operating.
The change in 225c0dda80 (#5511) results in
conflicts being immediately scanned and synced, while the test expects just one
conflict on either side. Change it to expect the same conflict on both sides.
We need to reset prevSeq so that we force a full check when someone
reconnects - the sequence number may not have changed due to the
reconnect. (This is a regression; we did this before f6ea2a7.)
Also add an optimization: we schedule a pull after scanning, but there
is no need to do so if no changes were detected. This matters now
because the scheduled pull actually traverses the database which is
expensive.
This, however, makes the pull not happen on initial scan if there were
no changes during the initial scan. Compensate by always scheduling a
pull after initial scan in the rwfolder itself.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/4508
LGTM: imsodin, AudriusButkevicius
After this change,
- Symlinks on Windows are always unsupported. Sorry.
- Symlinks are always enabled on other platforms. They are just a small
file like anything else. There is no need to special case them. If you
don't want to sync some symlinks, ignore them.
- The protocol doesn't differentiate between different "types" of
symlinks. If that distinction ever does become relevant the individual
devices can figure it out by looking at the destination when they
create the link.
It's backwards compatible in that all the old symlink types are still
understood to be symlinks, and the new SYMLINK type is equivalent to the
old SYMLINK_UNKNOWN which was always a valid way to do it.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3962
LGTM: AudriusButkevicius
Since delta indexes it's perfectly normal for us to need files that are
currently unavailable due to devices being disconnected. This doesn't
imply a failure, so we should not show the "Failed Items" line and
corresponding eternal spinner (since it would never be filled in, since
there is no failure).
We still show state "Out of Sync" (correct) and the list of files we
need (correct).
These are no longer required with Go 1.7. Change made by removing the
functions, doing a global s/osutil.Remove/os.Remove/.
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3514
This adds a new nanoseconds field to the FileInfo, populates it during
scans and sets the non-truncated time in Chtimes calls.
The actual file modification time is defined as modified_s seconds +
modified_ns nanoseconds. It's expected that the modified_ns field is <=
1e9 (that is, all whole seconds should go in the modified_s field) but
not really enforced. Given that it's an int32 the timestamp can be
adjusted += ~2.9 seconds by the modified_ns field...
GitHub-Pull-Request: https://github.com/syncthing/syncthing/pull/3431
